What is a rammer, and when do you use one?
Rammer: a walk-behind machine whose engine drives a single ramming shoe up and down in rapid blows, to compact cohesive soil in trenches and other narrow spaces.[9][10][3][11]
Also called Tamping rammer, Jumping jack, Trench rammer, Vibratory rammer
- A rammer drives one shoe up and down by its engine. A rental guide matches it to cohesive soil such as silt and clay, trenches and tight spaces, where a plate compactor suits granular soil and level ground.
- One maker's sheet gives three four-stroke rammers of 65 to 71 kg operating weight with a 280 by 340 mm shoe, 17 to 19 kN of impact force and 689 blows per minute. Another maker's heaviest rammer weighs 92 kg, has a 330 mm plate and runs on diesel.
- A maker's sheet gives the hand-arm vibration of its rammers as 9.4 to 10 m/s². South Africa's 2024 regulations set an action level of 2,5 m/s² and a limit of 5 m/s², both over 8 hours, so the operator's time on the machine matters.
Need one?Compactor hire: plate or rammerPlant hire
Headcore14 sources
Tell us about the compaction
What is a rammer, and how does it differ from a plate compactor?
A rammer is a compactor with a small foot that delivers blows rather than shaking a plate. A rental guide says rammers, also known as tampers, focus high-energy impacts through a compact shoe, suit cohesive or semi-cohesive soils such as silt and clay, and fit trenches and tight spaces where you need depth and control. It lists backfilling, footing preparation and work next to structures as uses.[9]
Wikipedia describes the mechanism: the foot is mounted on a sleeve that slides vertically in the leg, and inside the sleeve a piston is driven up and down by the engine through a reduction gear, crank and connecting rod. The vibrating motion is slightly off the vertical, which gives the rammer a tendency to "walk" forwards. It says the rammer, or trench rammer, is mainly used to compact the backfill in narrow trenches.[10]
The machine goes by several names. A hire catalogue describes its 115 to 130 lb jumping jack (about 52 to 59 kg, converted here) as a rammer suited to compaction work in trenches, and files it under "Jumping Jack Tampers/ Rammers". A Romanian catalogue titles its range "Tamping Rammers (Jumping Jacks)". On this page, rammer means that walk-behind tamping machine.[11][12][10]
The plate compactor is the other light machine: it combines weight and vibration for granular soils and covers more area per pass, according to the same rental guide. Rollers are covered on the padfoot roller page, and the compactor hire page sets out how to choose between them.[9]
What sizes of rammer are there?
The rows below are published ranges from three makers: a worked sample, not a standard size class. The makers state weight differently (operating weight in two, complete product without side-packed articles in the third), and one gives no impact force or blow rate on its product pages, so ask the hire company for the sheet of the model it offers.[3][5][6][7][8]
| Range | Weight | Shoe or plate width | Impact force and blows per minute | Engine and stated use |
|---|---|---|---|---|
| One maker's four-stroke rammers, three models | Operating weight 65 to 71 kg | Ramming shoe 280 mm wide and 340 mm long | 17 to 19 kN; 689 blows per minute | Single-cylinder 121 cm³ gasoline engine, fuel consumption 1 l/h; the page states no use |
| A second maker's four-stroke rammer, in two shoe widths | Operating weight 66 kg | 280 mm, or 200 mm in the narrow version | 700 blows per minute; impact force not stated | 4-stroke gasoline engine of 2.7 kW; sand, gravel or cohesive soils, trench compaction, foundation work, small paved areas and asphalt repairs |
| A third maker's three tamping rammers: two petrol, one diesel | 60 to 92 kg, complete product without side-packed articles | Plate width 150 to 330 mm; the heaviest model, 92 kg, has the 330 mm plate and the diesel engine | Not stated on the product pages | Granular and cohesive soils such as clay and silt; trenches and narrow spaces, for example around pillars and pipes |
Which engine does a rammer have, and can it run in a trench?
Most of the sheets read here list four-stroke gasoline engines. A maker's two-stroke range, on an undated sheet whose file was created in 2015, runs a two-cycle gasoline engine with oil injection from separate fuel and oil tanks, which removes premixing, at a fuel to oil ratio of 120:1. Its three weight classes have operating weights of 130, 145 and 163.1 lb (about 59, 66 and 74 kg, converted here) and 700, 700 and 650 blows per minute, with an 11 by 13 inch shoe (about 280 by 330 mm, converted here). Ask the hire company which engine it supplies and who provides the fuel and oil.[3][5][4]
The exhaust matters in a trench. The UK's Health and Safety Executive, whose guidance is practice here and not South African law, lists petrol-powered equipment used indoors or in enclosed spaces, including trenches and excavations, as a carbon monoxide risk: specially selected mechanical extraction that vents to the outside will almost always be needed, and it advises safer alternatives such as electrical tools where you can.[13]
Moisture decides the result. The rental guide says soil that is too dry will not knit and soil that is too wet can pump or smear, and advises removing debris and large rocks so the shoe meets the soil evenly. For the layer thickness and density to ask for, see the plate compactor page.[9]
A hire request should state the soil, the trench width and depth against the shoe width, the layer thickness and density the specification asks for, the weight you can load and lift, and who tests the density.[9][3][5]
What noise, vibration and trench rules apply to a rammer in South Africa?
The Physical Agents Regulations, 2024 set the hand-arm vibration action level at 2,5 m/s² and the occupational exposure limit at 5 m/s², both as 8-hour averages (Table 1). The four-stroke sheet's 9.4 to 10 m/s² is above both, and the UK Health and Safety Executive assesses daily exposure from the vibration level and the "trigger time" the hands are actually on the vibrating machine. The employer's duties at each level, and the noise limits and hearing protection rules, are set out on the plate compactor page.[1][3][14]
Trench work has its own duty. Regulation 13(2)(b) of the Construction Regulations, 2014 says a contractor who performs excavation work may not require or permit any person to work in an excavation that has not been adequately shored or braced. Shoring and bracing may not be necessary where the sides are sloped to at least the maximum angle of repose, or where the excavation is in stable material and the appointed competent person has given written permission after evaluating the site; where doubt about the soil's stability remains, a professional engineer or professional technologist competent in excavations decides, in writing.[2]
A worked example
A maker's sheet for a 280 mm shoe gives a forward running speed of 12 m/min and an area capacity of 202 m²/h. Those agree: 12 x 0.28 x 60 = 201.6 m²/h. For a trench 30 m long and 0.6 m wide, one coverage is 30 x 0.6 = 18 m². At the sheet's 202 m²/h that takes 18 / 202 x 60 = 5.3 minutes of ramming. The sheet gives no number of coverages or layer thickness, so the time for the trench is that figure times the coverages needed to reach the specified density, times the layers.[3]
Questions buyers ask
Is a jumping jack the same as a rammer?
Yes, in the sources read here. A hire catalogue describes its 115 to 130 lb jumping jack (about 52 to 59 kg, converted here) as a rammer suited to compaction work in trenches, and a Romanian catalogue titles its range "Tamping Rammers (Jumping Jacks)". In a request, give the weight and shoe width as well as the name.[11][12]
How heavy is a rammer, and how wide is its shoe?
In the ranges read here, from about 60 to 92 kg, though makers measure weight differently. One maker's four-stroke rammers weigh 65 to 71 kg in operating weight with a 280 mm shoe; a second maker's weighs 66 kg with a 280 mm or 200 mm shoe; a third maker's three rammers weigh 60 to 92 kg with plates of 150 to 330 mm. Check the shoe against the trench width.[3][5][6][8]
How much vibration does a rammer produce?
One maker's sheet lists an average hand-arm vibration of 10 m/s² for two of its four-stroke rammers and 9.4 m/s² for the third. South Africa's action level is 2,5 m/s² and its limit 5 m/s² over 8 hours. The UK Health and Safety Executive warns that some manufacturers' data may underestimate workplace vibration substantially.[3][1][14]
Tell us about the compaction
Sources
- Department of Employment and Labour (Government Gazette 52226), Physical Agents Regulations, 2024 (Notice 5952), 6 March 2025.
- Department of Labour (Government Gazette 37305), Construction Regulations, 2014 (GN R. 84), 7 February 2014.
- Wacker Neuson, 4 Stroke Rammers: technical data (UK site), Undated product page; copyright 2022 to 2026.
- Wacker Neuson (sheet hosted by a US dealer), BS50-2i, BS60-2i, BS70-2i: 2 Stroke Rammer, Undated two-page data sheet; file created 15 July 2015 (PDF metadata), read 19 November 2026.
- Weber Maschinentechnik, Vibratory rammer SRV 620 (technical data), Last update 18 November 2026 (page footer).
- Husqvarna Construction, Husqvarna LT 5005 tamping rammer (product page), Undated product page, read 19 November 2026.
- Husqvarna Construction, Husqvarna LT 6005 tamping rammer (product page), Undated product page, read 19 November 2026.
- Husqvarna Construction, Husqvarna LT 8005 tamping rammer (product page), Undated product page, read 19 November 2026.
- Cat Rental Store (Caterpillar), Light compactors: types, uses, and how to choose, Undated blog page; copyright 2026.
- Wikipedia, Compactor, Last edited 24 March 2026.
- Termix.ro, Professional Tamping Rammers (Jumping Jacks), Undated catalogue page; copyright 2026.
- Sunbelt Rentals, Jumping Jack Tamper 115-130lb Class (rental catalogue page), Undated product page, read 19 November 2026.
- Health and Safety Executive (UK), Construction hazardous substances: carbon monoxide, 7 November 2024.
- Health and Safety Executive (UK), Vibration risk assessment, 8 July 2025.