Skip to content

What is a padfoot roller, and when do you need one?

Padfoot roller: a roller whose steel drum carries raised pads, or feet, that press into cohesive soil such as clay or silt and compact it, built as a ride-on, a drum shell or a trench roller.[6][7][11]

Also called Pad foot roller, Sheepsfoot roller, Padfoot compactor, Padfoot drum

  • A padfoot drum suits cohesive soils such as clay, silt and loam. For gravel and sand a roller maker points to smooth drums, and a flat final surface is left to a smooth drum.
  • Padfoot rollers come as single-drum ride-on machines, as pad shells fitted over a smooth drum, and as remote-controlled trench rollers. One maker's maximum operating weights run from 1,456 kg for a trench roller to 14,330 kg for a ride-on; a Western Cape tender asked for padfoot rollers in classes of 10 to 18 ton.
  • The South African documents read here give no layer thickness for padfoot rolling itself. An Eastern Cape specification caps trench backfill layers at 150 mm after compaction and asks 93% of modified AASHTO density in cohesive soil under traffic.

Need one?TLB hire with an operatorPlant hire

Headcore13 sources

What work do you need done?

What is a padfoot roller and what does it do to the soil?

A padfoot roller is a roller whose steel drum carries raised pads that press into the soil as the drum turns. A roller maker's soil guidance says "Cohesive soils are best compacted using compactors with padfoot drums and high amplitudes", and describes cohesive soils such as loam, clay or silt as soils whose particles adhere to each other.[6]

Padfoot and sheepsfoot are often used as names for the same machine. Wikipedia describes initial compaction of a road substrate with "a padfoot or "sheep's foot" drum roller", and captions a large soil roller "sheepsfoot". A New Zealand forest road manual groups "sheep and pad foot rollers" as kneading compactors with high point loads for cohesive soils, but describes the feet by type: tapered prongs on a sheep-foot roller, and wider, shorter, closer and often diamond-shaped feet on a tamping-foot roller. So ask a hire company for the drum type, the number of pads and their height rather than relying on either name.[7][12][13]

The pads change how the drum works the soil. The roller maker says the trapezoidal studs on the drum leave impressions in the soil and increase the surface area so that the soil can dry out, and its shell data sheet speaks of faster drying of cohesive material. A New Zealand forest road manual says sheep-foot rollers perform best on cohesive soils at or drier than optimum moisture content, and tend to walk out of the fill as compaction occurs, with the feet riding on the compacted surface.[6][11][7]

The pads come on three kinds of machine. One maker's padfoot shells are segments, two or three to a drum, that convert a smooth-drum compactor quickly into a padfoot compactor. A single-drum ride-on is built with the padfoot drum. One maker's trench roller has two padfoot drums and an infrared remote control with three sensors to keep line of sight; Wikipedia captions a trench roller as operated by remote control for operator safety.[11][9][8][12]

Rates, wet and dry hire, the water cart and transport are in the article on road-building plant; this page is about the machine.[5]

What sizes of padfoot roller are there?

The rows below are published figures from one maker's range and the classes of one municipal tender: a worked sample, not a standard size class. Weights change with cab, canopy and options, so ask the hire company for the data sheet of the machine it offers.[8][9][10][11][5]

What sizes of padfoot roller are there?
TypeWeightDrum widthPads and vibrationStated use
Trench roller, two padfoot drums1,456 kg maximum operating weight820 mm each drum570 mm drum diameter; 42 Hz, 2.32 mm amplitude, 72 kN centrifugal forceTrench roller with an infrared remote control
Single-drum ride-on, mid size10,890 kg with cab; 12,420 kg maximum2,140 mm140 pads, each 100 mm high; 27 or 37 Hz, 1.90 or 0.80 mm amplitudeCompactor with a padfoot drum; padfoot drums suit cohesive soils
Single-drum ride-on, larger12,680 kg with cab; 14,330 kg maximum2,140 mm30 or 33 Hz, 1.8 or 0.8 mm amplitude; 250 or 130 kN centrifugal forceCompactor with a padfoot drum; padfoot drums suit cohesive soils
Padfoot shell for a smooth-drum compactor, three sizes454 kg, 650 kg and 1,420 kg to 1,460 kg per drum1,370 mm, 1,680 mm and 2,140 mm60, 84 and 120 pads; 100 or 156 cm² end face eachCohesive and mixed soils, and part of cold recycling
Padfoot road roller with operator, municipal tender classes10, 12, 15 and 18 tonNot statedNot statedEach class to be priced with a wet rate and a standby rate

Sources:[8][9][10][11][5][6]

When should I not use a padfoot roller, and what layer and density apply?

Not as the first choice on granular material, and not for the final surface. The roller maker says "non-cohesive soils are more effectively compacted with smooth drums and lower amplitudes". A New Zealand forest road manual says sheep-foot and tamping rollers do not produce a smooth surface, and that smooth drum vibrating rollers and pneumatic-tyre rollers are used as finishing rollers for clay and clayey sand subgrades. Wikipedia likewise says that once the soil base is flat the pad drum compactor is no longer used on the road surface.[6][7][13]

The South African documents read for this page give no layer thickness for padfoot rolling in particular, so the thickness comes from the engineer's specification for the job. The Eastern Cape specification for on-farm infrastructure sets trench backfill in layers not exceeding 150 mm after compaction. Under road traffic loads it asks 93% of modified AASHTO maximum dry density in cohesive soil and 98% in non-cohesive soil; elsewhere it asks the density of the surrounding ground or 90%, whichever is higher.[3]

Wikipedia names another machine for trench backfill: it says the rammer, or trench rammer, is mainly used to compact the backfill in narrow trenches (see rammer).[12]

The CSIR settlement guidelines say standard practice "should be to roll the layer to refusal density based on proof rolling of a short section prior to its full compaction". Put in the request the soil, the layer thickness and density the specification asks for, and who tests the density.[4]

What rules apply to a padfoot roller on a South African site?

Regulation 1 of the Construction Regulations, 2014 defines mobile plant as machinery "able to move independently" and used for construction work on a construction site, which covers a ride-on or trench roller. Regulation 23(1)(d) requires its operator to have received appropriate training, be certified competent with proof of competency, be authorised in writing, and hold a medical certificate of fitness in the form of Annexure 3.[1]

The rest of regulation 23 applies too: the protective structure, the daily inspection and edge protection at excavations. A ride-on roller also exposes its operator to whole-body vibration, which the Physical Agents Regulations, 2024 limit to 1,15 m/s² as an 8-hour average.[1][2]

A worked example

A service trench under a road is backfilled with 0.6 m of cohesive soil. The Eastern Cape specification caps each layer at 150 mm after compaction and asks 93% of modified AASHTO density in cohesive soil under traffic, so the backfill needs at least 600 / 150 = 4 layers, each compacted to 93%. If the machine is a walk-behind roller, the same specification's note says a layer over 100 mm is extremely difficult to compact to density and a 150 mm layer should go in as two 75 mm layers, so the trench needs 600 / 75 = 8 layers.[3]

Questions buyers ask

Is a sheepsfoot roller the same as a padfoot roller?

Often the names are used for the same machine: Wikipedia writes of a padfoot or sheep's foot drum roller. A New Zealand forest road manual groups sheep and pad foot rollers as kneading compactors for cohesive soil, and gives sheep-foot rollers tapered prong feet and tamping-foot rollers wider, shorter, closer feet. So specify the pad count, pad height and drum width in a request.[7][13][9]

Can a smooth-drum roller be fitted with pads?

On some machines, yes. One maker sells padfoot shells in two or three segments for its smooth-drum compactors, with a quick and easy conversion, and lists their weights per drum from 454 kg to 1,460 kg. Ask the hire company whether a shell is fitted, and for the operating weight with it.[11]

Can a padfoot roller finish the surface?

No. The pads leave impressions in the soil. A New Zealand forest road manual says sheep-foot and tamping rollers do not produce a smooth surface, and that smooth drum vibrating rollers and pneumatic-tyre rollers are used as finishing rollers for clay and clayey sand subgrades. Wikipedia says the pad drum compactor is no longer used once the soil base is flat.[6][7][13]

What size padfoot roller should a request ask for?

Ask for a class and the layer it must serve. A Cape Winelands district tender asked for padfoot road rollers with an operator in classes of 10, 12, 15 and 18 ton, each to be priced with a wet rate and a standby rate. For trench work there are trench rollers; one maker's weighs 1,456 kg at most.[5][8]

What work do you need done?

Sources

  1. Department of Labour (Government Gazette 37305), Construction Regulations, 2014 (GN R. 84): regulations 1, 13 and 23, 7 February 2014.
  2. Department of Employment and Labour (Government Gazette 52226), Physical Agents Regulations, 2024 (Notice 5952): regulation 13 and Table 1, 6 March 2025.
  3. Department of Rural Development and Agrarian Reform, Eastern Cape (Directorate Engineering Services), DRDAR SCMM-03/2024: Specification of construction materials and methods to be used for agricultural on-farm infrastructure (clause 2.16, compaction of trench backfill), Third edition, April 2024 (file posted April 2026).
  4. CSIR (for the Department of Housing), Guidelines for Human Settlement Planning and Design, Volume 2, Chapter 8: Roads: materials and construction, PDF of 22 October 2009.
  5. Cape Winelands District Municipality, Tender T 2025/015: the hiring of mechanical and construction plant equipment for the period ending 30 June 2028 (specification and pricing schedules), Closing date 19 March 2025.
  6. Wirtgen Group, Soil compaction (earthworks applications), Read 19 November 2026.
  7. New Zealand Forest Owners Association, NZ Forest Road Engineering Manual, 6.6 Compaction equipment, Undated page, copyright 2026, read 19 November 2026.
  8. Hamm AG (Wirtgen Group), Trench roller with two vibration padfoot drums HTC 15 (technical data), Undated product page, read 19 November 2026.
  9. Hamm AG (Wirtgen Group), 3410 P (H217): compactor with padfoot drum, technical data, Datasheet, copyright 2023 (V5), read 19 November 2026.
  10. Hamm AG (Wirtgen Group), HC 120i P (H252): compactor with padfoot drum, technical data, Datasheet, copyright 2026 (V16), read 19 November 2026.
  11. Hamm AG (Wirtgen Group), Padfoot shells: technical data (optional equipment), Undated datasheet, read 19 November 2026.
  12. Wikipedia, Compactor, Last edited 24 March 2026.
  13. Wikipedia, Road roller, Last edited 20 October 2026.