How do you read a crane load chart?
Load chart: the manufacturer's table of the loads a crane may lift at each working radius and boom length, under the stated support and reeving conditions, posted where the operator can see it.[1][5]
Also called Load table, Rated capacity chart, Lifting capacity chart
- A crane load chart lists the rated load for each working radius and boom length, for one stated set-up: how far the outriggers are extended, which way the boom points, how many parts of line, and which hook is fitted.
- Capacity falls quickly as the radius grows and changes with the support. One maker's published chart for a 25 t crane gives 16.30 t at 6.0 m on the 9.35 m boom with the outriggers fully extended, and 2.80 t at the same radius and boom on rubber.
- In South Africa the Driven Machinery Regulations require the safe working load to be marked and, where it varies with the conditions of use, a table of it posted where the operator can see it.
Need one?Crane hire and crane trucksPlant hire
Headcore5 sources
Tell us about the lift
What does a crane load chart show?
A crane load chart shows the maximum load the crane may lift for each combination of working radius and boom length, for one set-up. In the 25 t chart used on this page, radius runs down the side and boom length across the top, and each figure applies only to the outrigger setting printed above it.[5]
One maker's published chart for a 25 t rough terrain crane gives five such conditions: outriggers fully extended (6.6 m) for 360 degrees, three intermediate outrigger extensions (6.0 m, 5.0 m and 3.8 m) over the side, and the outriggers fully retracted, over the side. Its chart for work without outriggers adds stationary and pick and carry operation, with separate figures over the front and for the full range.[5]
The chart also names the hook and the parts of line for each boom. On outriggers the standard is 7 parts of line on the 9.35 m boom, 6 on the 16.4 m boom and 4 on the 23.45 m and 30.5 m booms; without outriggers it is 4 throughout. The figures assume a crane that is level on firm ground and, off outriggers, tyres at the rated pressure.[5]
The radius is the actual working radius, allowing for deflection of the boom. The chart's own note says to operate the crane on the basis of the working radius.[5]
How do outriggers and boom length change the rated load?
Support changes the rating more than most readers expect. Read from the same published 25 t chart at a 6.0 m working radius, the rated load in tonnes depends on the outrigger setting and the boom length:[5]
| Support at 6.0 m radius | 9.35 m boom | 16.4 m boom | 23.45 m boom | 30.5 m boom |
|---|---|---|---|---|
| Outriggers fully extended, 6.6 m | 16.30 | 15.05 | 12.20 | 8.00 |
| Outriggers extended 6.0 m, over the side | 16.30 | 15.05 | 12.20 | 8.00 |
| Outriggers extended 5.0 m, over the side | 12.20 | 12.00 | 12.20 | 8.00 |
| Outriggers extended 3.8 m, over the side | 7.45 | 7.30 | 8.05 | 7.95 |
| Outriggers fully retracted, over the side | 3.40 | 3.25 | 3.90 | 3.55 |
| On rubber, stationary, 360 degrees | 2.80 | 2.55 | 3.10 | not rated |
Sources:[5]
What must you deduct before comparing your load with the chart?
Read the notes printed on the chart first. The note to this 25 t chart says its values include the mass of the main hook and slings for boom work, and of the auxiliary hook and slings for jib work; the 25 t hook weighs 220 kg. So the hook and slings take up part of each figure, and the load itself must be lighter by their mass. The hook fitted and its mass are printed on each chart, so read the notes on the chart for the crane in front of you.[5]
The notes add two more deductions. Working the boom with the jib rigged, subtract 2,400 kg plus the mass of all hooks and slings attached to the boom from each boom capacity, with an upper limit of 14 t. The rooster sheave is rated at the boom capacity minus the mass of all hooks and slings attached to the boom, up to 4,000 kg.[5]
Two more rules decide which figure to read. If the radius or boom length falls between printed values, use the rated value or the next one, whichever gives the smaller capacity. And where the chart prints a critical boom angle for a boom length and outrigger setting, the crane can tip over below it even unloaded, so the boom is never lowered under that angle.[5]
The chart's notes say the figures inside the area bordered with a thick line are based on structural limitations and the others on stability limitations. With a non-standard number of parts of line, the chart limits each rope to 37.2 kN (3.8 tf).[5]
What does South African law say about the load chart?
Regulation 18(1)(b) of the Driven Machinery Regulations, 2015 (GN R. 540) bars use of a lifting machine unless it is "conspicuously and clearly marked with the safe working load". Where the safe working load varies with the conditions of use, "a table showing the safe working load with regard to every variable condition shall be posted by the user in a conspicuous place easily visible to the operator". That table is the load chart.[1]
The guidelines add in a note that the end user "must determine the safe working load (SWL) as per the prevailing conditions". Regulation 1 defines the safe working load as the mass load determined by a competent person taking into account the environment and operating conditions; the correction notice GN R. 913 of 2015 restates that definition and adds that "Working Load Limit" has a corresponding meaning.[4][2][1]
Regulation 18(9) bars the use of a power-driven lifting machine unless it is provided with, "in the case of a power-driven lifting machine with a lifting capacity of greater than 5 000 kg, a load indicator capable of indicating to the operator of the machine the mass of the load being lifted", "and/or" a load-limiting device that "will automatically arrest the driving effort whenever the load being lifted is greater than the safe working load of the power-driven lifting machine at that particular radius". A proviso says power-driven lifting machines manufactured or refurbished before the regulations commenced "shall be deemed to comply with these Regulations". The manufacturer's identification plate (regulation 18(1)(c)) names the manufacturer, the design standard, the serial or reference number and the country of origin.[1]
A lifting machinery inspector examines and performance-tests the machine before first use and at intervals not exceeding 12 months, as prescribed by the standard it was manufactured to; where there is no manufacturing standard or incorporated standard, the whole installation is tested with 110% of the safe working load applied over the complete lifting range (regulation 18(5)(a)). Notice GN R. 542 incorporates SANS 19 for the inspection, testing and examination of mobile cranes.[1][3]
A worked example
A site needs a 14 t load placed at a working radius of 6.0 m, using the published 25 t chart with the outriggers fully extended at 6.6 m. On the 9.35 m boom the chart gives 16.30 t at 6.0 m. That figure includes the 220 kg main hook and the slings, so the load and hook come to 14.22 t and the lift passes only if the slings weigh less than the remaining 2.08 t. If the site only allows the outriggers out to 5.0 m, the same radius gives 12.20 t over the side and the lift fails there; on rubber it gives 2.80 t through 360 degrees. A measured radius of 6.2 m is read at the next printed value, 6.5 m, which gives 15.10 t. At 8.0 m on fully extended outriggers the best figure is 11.10 t on the 16.4 m boom, so a 14 t load at that radius needs a larger crane.[5]
Questions buyers ask
Where do I find the load chart for a hired crane?
Where the operator can easily see it. Regulation 18(1)(b) makes the user post the table of safe working loads in a conspicuous place easily visible to the operator. Ask the crane company for the chart for the boom length and radius your lift needs, with the quote.[1]
Is the load chart the same as a load indicator?
No. The chart is the table of rated loads. A load indicator is a device that shows the operator the mass being lifted, and a load-limiting device stops the driving effort above the safe working load at that radius. Regulation 18(9) requires a load-limiting device and/or, for a machine with a lifting capacity of greater than 5 000 kg, a load indicator.[1]
Why is capacity lower on a longer boom at the same radius?
Usually, but read the column for the boom you will use: the rating is set per boom length. On the published 25 t chart at a 6.0 m radius on fully extended outriggers, the 9.35 m boom gives 16.30 t, the 23.45 m boom 12.20 t and the 30.5 m boom 8.00 t. With the outriggers at 3.8 m, though, the 23.45 m boom gives 8.05 t against 7.30 t on the 16.4 m boom.[5]
Can I use a chart for another crane of the same size?
No. The chart belongs to the crane's model and configuration. The manufacturer's identification plate names the design standard and the serial or reference number (regulation 18(1)(c)).[1]
Tell us about the lift
Sources
- Department of Labour (Government Gazette 38905), Driven Machinery Regulations, 2015 (GN R. 540), 24 June 2015.
- Department of Labour (Government Gazette 39253), Driven Machinery Regulations, 2015: correction notice (GN R. 913), 2 October 2015.
- Department of Labour (Government Gazette 38905), Incorporation of safety standards into the Driven Machinery Regulations, 2015 (GN R. 542), 24 June 2015.
- Department of Labour (Government Gazette 40734), Guidelines for Driven Machinery Regulations, 2015 (GN R. 288, Rev 0), 31 March 2017.
- Kato Works Co., Ltd., SR-250R rough terrain crane: specification and rated lifting capacity (catalogue C03351, printed code 12.2012-1000 (TI) 1), undated.