What does SWL mean, and how does it differ from WLL?
Safe working load: the mass load applicable to a piece of equipment or system as determined by a competent person taking into account the environment and operating conditions.[1][2]
Also called SWL, Working load limit (WLL), Rated capacity
- In South Africa the Driven Machinery Regulations define safe working load as a mass set by a competent person for the conditions of the lift. A 2015 correction notice adds that Working Load Limit has a corresponding meaning.
- The department's own guidelines read it this way: WLL is the manufacturer's marking, part of the design specification, and the end user determines the SWL for the prevailing conditions.
- A crane, a chain sling, a wire rope sling, a shackle and a hook are each set, marked and examined differently, and a sling angle cuts the rating of a two-leg sling.
Need one?Crane hire and crane trucksPlant hire
Headcore7 sources
Tell us about the lift
What does SWL mean, and is it the same as WLL?
SWL means safe working load. Regulation 1 of the Driven Machinery Regulations, 2015 (GN R. 540) defines it as "the mass load applicable to a piece of equipment or system as determined by a competent person taking into account the environment and operating conditions". The definition of a competent person was corrected by GN R. 913 of 2 October 2015, and now also requires that the person "is familiar with the Act and with the applicable regulations made under the Act".[1][2]
The same correction notice adds a definition: "Working Load Limit" has a corresponding meaning. The Department of Labour's guidelines to the regulations (GN R. 288 of 2017) add in a note that lifting tackle marked with a Working Load Limit is also acceptable as complying with regulation 18(10).[2][3]
The same guidelines draw a practical line. They describe WLL as an international marking attached to a machine when it is bought from the manufacturer, and as part of the design specification. They say the end user must determine the SWL "as per the prevailing conditions", and that the rigger must determine it "based on the condition at the time of lifting".[3]
In practice, read the marked figure as the starting point and work out the SWL for the day. The UK Health and Safety Executive says a marked SWL may have to be reduced (derated) for where and how the equipment is used, with the angle of a sling's legs and a sling used with fewer than all its legs among its examples. It also says other phrases, such as rated capacity, are sometimes used to mean the SWL.[6]
How is the SWL set, marked and examined for each item?
The regulations treat a lifting machine and lifting tackle differently. Regulation 18 of GN R. 540 covers both. Notice GN R. 542 incorporates SANS 19 for the inspection, testing and examination of mobile cranes. It also incorporated SANS 2972, on lifting tackle inspection, until GN R. 483 of 11 May 2018 removed it from the schedule.[1][5][4]
| Item | What sets its SWL or WLL | Where it is marked | Examination |
|---|---|---|---|
| Crane (lifting machine) | The manufacturer's design. Where the SWL varies with the conditions of use, the user posts a table of the SWL for every variable condition where the operator can see it (regulation 18(1)(b)). Regulation 18(9) calls for a load indicator and/or a load-limiting device that arrests the driving effort when the load is above the SWL at that particular radius. | Conspicuously and clearly marked with the SWL, plus the manufacturer's identification plate (regulation 18(1)(b) and (c)). | Examination and performance test by a lifting machinery inspector before first use, after re-erection and at intervals not exceeding 12 months; ropes, chains, hooks, sheaves, brakes and safety devices by a competent person at intervals not exceeding six months (regulation 18(5)(a) and (6)). |
| Chain sling | The chain's strength against a factor of safety of five for steel chain or four for high-tensile or alloy steel chain. Where two or more chains share the load equally, the factor of safety may be calculated on the sum of their breaking strengths, taking the angle of loading into account (regulation 18(10)(c)). | The lifting assembly is marked with traceable identification particulars and the SWL it is designed to lift (regulation 18(10)(b)). | Examined at intervals not exceeding three months by a competent person appointed in writing, who records and signs the result (regulation 18(10)(e)). |
| Wire rope sling | The rope's strength against a factor of safety of six, or eight for double-part spliced endless sling legs and double-part endless grommet legs (regulation 18(10)(c)). | As for a chain sling: the assembly carries traceable identification and the SWL (regulation 18(10)(b)). | Every three months by a competent person appointed in writing (regulation 18(10)(e)). |
| Shackle | No figure is set in the regulation: it must be well constructed of sound material, strong enough, free from defects and built to a generally accepted technical standard (regulation 18(10)(a)). | Regulation 18 marks the lifting assembly. Guidance from the UK Health and Safety Executive, which is not South African law, says a lifting accessory with one SWL, such as a shackle, should have it marked on the accessory, or carry a coding system where marking is not possible. | Lifting tackle, so every three months by a competent person appointed in writing (regulation 18(10)(e)). |
| Hook | On a crane, a hook in the load path must be designed so the load cannot disconnect accidentally (regulation 18(4)); in a sling assembly, it is tackle built to a generally accepted technical standard. | Regulation 18 sets no separate marking for a hook: it requires the lifting machine (regulation 18(1)(b)) and the lifting assembly (regulation 18(10)(b)) to be marked with the SWL. | On a crane, in the six-monthly examination; as tackle in a sling assembly, every three months. |
What must a South African user do about the SWL of a hired crane?
Keep the machine inside its SWL at every radius. A power-driven lifting machine needs a load-limiting device that arrests the driving effort when the load exceeds the SWL at that particular radius and/or, where its lifting capacity is greater than 5 000 kg, a load indicator showing the mass being lifted (regulation 18(9)). When you ask for a crane through crane hire, ask for the load chart for the radius you need.[1]
The machine is tested against the SWL. Where there is no manufacturing standard or incorporated standard, regulation 18(5)(a) requires the whole installation to be tested with 110% of the SWL applied over the complete lifting range.[1]
For a leased machine, regulation 18(7)(b) makes the user keep on its premises the latest performance test and service records, not older than 12 months.[1]
Slings, shackles and other tackle must be inspected and discarded if they show any sign of damage, defect, wear or distortion that would make them unsafe (regulation 18(10)(d)). Where equal load sharing is not possible, the guidelines say the person doing the work must allow for unequal loading in determining the capacity.[1][3]
How does a sling angle reduce the safe working load?
A wider angle between the legs of a two-leg sling cuts the load the sling can carry, because each leg then pulls at a slant. The LEEA lifting code of practice gives two ways to rate a two-leg sling, with the angle measured from the vertical.[7]
Its uniform load method, which the code recommends for all multipurpose slings, rates the sling at 1.4 times the WLL of a single leg from 0 to 45 degrees to the vertical, and at 1.0 times from 45 to 60 degrees. Its trigonometric method gives 2 times the single-leg WLL times the cosine of the angle to the vertical, and the code strongly recommends it only for slings designed for a single purpose, or where a national standard permits it.[7]
Where two single-leg slings are used together as a two-leg sling, the code recommends joining their upper ends with a shackle or link, says the legs must be placed symmetrically, and says a leg should not exceed 45 degrees to the vertical. Regulation 18(10)(c) also allows the factor of safety to be calculated on the sum of the breaking strengths, taking the angle of loading into account, where two or more chains or ropes share a load equally.[7][1]
A worked example
A two-leg sling has legs with a single-leg WLL of 2 t each, and the load is 3 t. By the uniform load method, which the code recommends for a multipurpose sling, it is rated 1.4 × 2 = 2.8 t anywhere from 0 to 45 degrees to the vertical, so the 3 t load needs a larger sling. A sling rated by the trigonometric method for a single purpose would give 2 × 2 × cos 30 = 3.46 t with the legs at 30 degrees to the vertical, 2 × 2 × cos 45 = 2.83 t at 45 degrees, which is below 3 t, and 2 × 2 × cos 60 = 2.0 t at 60 degrees.[7]
Questions buyers ask
What does SWL stand for?
Safe working load. South Africa's Driven Machinery Regulations define it as the mass load applicable to a piece of equipment or system as determined by a competent person, taking into account the environment and operating conditions.[1]
Is a working load limit the same as a safe working load?
In South African law, the two have a corresponding meaning (GN R. 913 of 2015), and tackle marked with a WLL is acceptable. The department's guidelines describe the WLL as the manufacturer's marking and say the end user determines the SWL for the prevailing conditions.[2][3]
Must a sling be marked with its safe working load?
A lifting assembly made of different items of tackle must be conspicuously and clearly marked with traceable identification particulars and the SWL it is designed to lift (regulation 18(10)(b)). The guidelines add that tackle marked with a WLL also complies.[1][3]
How often must slings and shackles be examined?
At intervals not exceeding three months, by a competent person the user appoints in writing, who records and signs the result (regulation 18(10)(e)). SANS 2972, on lifting tackle inspection, was incorporated by GN R. 542 in 2015 and removed from the schedule by GN R. 483 of 11 May 2018.[1][5][4]
Who decides the SWL for a crane lift?
Where the SWL varies with the conditions of use, regulation 18(1)(b) makes the user post a table of the SWL for every variable condition, the load chart, where the operator can easily see it. On the day, the guidelines say the rigger determines the SWL based on the condition at the time of lifting.[1][3]
Tell us about the lift
Sources
- Department of Labour (Government Gazette 38905), Driven Machinery Regulations, 2015 (GN R. 540), 24 June 2015.
- Department of Labour (Government Gazette 39253), Driven Machinery Regulations, 2015: correction notice (GN R. 913), 2 October 2015.
- Department of Labour (Government Gazette 40734), Guidelines for Driven Machinery Regulations, 2015 (GN R. 288, Rev 0), 31 March 2017.
- Department of Labour (Government Gazette 41622), Incorporation of safety standards into the Driven Machinery Regulations, 2015: amendment removing SANS 2972 (GN R. 483), 11 May 2018.
- Department of Labour (Government Gazette 38905), Incorporation of safety standards into the Driven Machinery Regulations, 2015 (GN R. 542), 24 June 2015.
- Health and Safety Executive (UK), Safe use of lifting equipment: Lifting Operations and Lifting Equipment Regulations 1998, Approved Code of Practice and guidance (L113), Second edition 2014, with amendments 2018.
- Lifting Equipment Engineers Association (LEEA), COPSULE, 1.A5.4 Principles for the selection of slings (Edition 10), Edition 10; page copyright 2026.